Tl494: Ltspice ^hot^

* TL494 behavioral subckt (switch-level) * Pins: VCC GND FB COMP RT CT DTC SS OUTC OUTE ILIM .SUBCKT TL494 VCC GND FB COMP RT CT DTC SS OUTC OUTE ILIM * Internal nodes .node 1 2 3 4 5 * Reference 5V (approx) BREF REF GND V=V(VCC)*0.08 ; simple reference scaled from VCC (adjust as needed) * Oscillator: ramp from C RRT RT REF 100k CCT CT REF 10n * Use behavioral current to form saw; simplistic: I = k/RT BIOSC SAW REF I=V(VCC)/(100k) ; replace with better oscillator if needed * Error amplifiers (inverting inputs: FB, ILIM; non-inv to reference) * EA1: drives COMP node EEA1 COMP GND VALUE = { clamp( (V(REF)-V(FB))*10, -5, 5 ) } * PWM comparator with deadtime (DTC pin sets min-off) BPD CMP_OUT GND V= if( V(COMP) > V(SAW)*(1 - V(DTC)/5), 1, 0 ) * Outputs: open-collector to drive gate driver resistor network * OUTC and OUTE are complementary PWM outputs (simple) EOUTC OUTC GND VALUE={ V(CMP_OUT) ? 0.1 : 0 } ; low impedance sink when active EOUTE OUTE GND VALUE={ !V(CMP_OUT) ? 0.1 : 0 } * Soft-start: clamp COMP by SS voltage BSS COMP LIMIT GND V= min(V(COMP), V(SS)) * Current limit sense: if ILIM > threshold reduce duty BLICM COMP GND V= if( V(ILIM) > 0.5, V(COMP)*0.5, V(COMP)) .ENDS Notes: This is a condensed, pragmatic starting point — refine slopes, gains, and the oscillator to match TL494 datasheet values (osc frequency set by RT/CT, deadtime control range, internal reference ≈5V, EA gains, output transistor drive limits). Purpose: verify startup, soft‑start and current‑limit.

tl494 ltspice
Enjoyx - site for adults only. Available content may contain pornographic materials. By continuing to Enjoyx you confirm that you are 18 or older. Read more about Parental Control Guide
tl494 ltspice
Cookies help provide the best experience for you Enjoyx uses cookies to provide you with the best personalized experience including enhancing your browsing experience, delivering personalized content, recommendations and advertisements, and more. For more details about cookies or to change your preferences, please refer to our Cookie Policy. For more details about how we process your personal data, please refer to our Privacy Policy.
Reject cookies
Exit Manage Accept all cookies
Cookies

* TL494 behavioral subckt (switch-level) * Pins: VCC GND FB COMP RT CT DTC SS OUTC OUTE ILIM .SUBCKT TL494 VCC GND FB COMP RT CT DTC SS OUTC OUTE ILIM * Internal nodes .node 1 2 3 4 5 * Reference 5V (approx) BREF REF GND V=V(VCC)*0.08 ; simple reference scaled from VCC (adjust as needed) * Oscillator: ramp from C RRT RT REF 100k CCT CT REF 10n * Use behavioral current to form saw; simplistic: I = k/RT BIOSC SAW REF I=V(VCC)/(100k) ; replace with better oscillator if needed * Error amplifiers (inverting inputs: FB, ILIM; non-inv to reference) * EA1: drives COMP node EEA1 COMP GND VALUE = { clamp( (V(REF)-V(FB))*10, -5, 5 ) } * PWM comparator with deadtime (DTC pin sets min-off) BPD CMP_OUT GND V= if( V(COMP) > V(SAW)*(1 - V(DTC)/5), 1, 0 ) * Outputs: open-collector to drive gate driver resistor network * OUTC and OUTE are complementary PWM outputs (simple) EOUTC OUTC GND VALUE={ V(CMP_OUT) ? 0.1 : 0 } ; low impedance sink when active EOUTE OUTE GND VALUE={ !V(CMP_OUT) ? 0.1 : 0 } * Soft-start: clamp COMP by SS voltage BSS COMP LIMIT GND V= min(V(COMP), V(SS)) * Current limit sense: if ILIM > threshold reduce duty BLICM COMP GND V= if( V(ILIM) > 0.5, V(COMP)*0.5, V(COMP)) .ENDS Notes: This is a condensed, pragmatic starting point — refine slopes, gains, and the oscillator to match TL494 datasheet values (osc frequency set by RT/CT, deadtime control range, internal reference ≈5V, EA gains, output transistor drive limits). Purpose: verify startup, soft‑start and current‑limit.

Reject Cookies
Cancel Save
tl494 ltspice tl494 ltspice